Two Cross Handle Wall Mounted Bathroom Faucet Polished Nickel 240.1950PN

$642.00
EA

This product is a 1/2” NPT connection valve and trim combo with two volume control handles separately for hot and cold water with single mixed output.

Handle Operation – The volume and temperature of the water are controlled by the two handles, HOT and COLD.

Valve Installation – As the valve [Part # WLM.1900] is installed, care should be taken to maintain a proper distance from the back of the valve to the surface of the finished tile which should be between 2.39” and 3.09”. Also, the valve must be installed horizontally and not at an angle. In case, a tile is thicker or wall is deep, extensions are used for elongating both handles of the valve to ensure the proper setting of the trim. Extension kits can be ordered separately in Chrome, Brushed Nickel, or other special finishes.

Cut Out Dimensions – The cut out in wall should be 3 holes, 1.3 inches in diameter which will properly be covered by the trim plates. This will ensure that the trim plate will cover the cut out hole in the wall.

Trims
 – The trims comprise of well-finished handle knobs, handle trims, cartridge covers, and spout. Depending upon the shower model, trims can be of different shape and size, varying from square to circular shower handles.

Limitations of Liability This warranty is applicable only to Isenberg products purchased after 1st January, 2011 and shall be effective from the date of purchase as shown on the purchaser’s receipt. It applies only to Isenberg products purchased from Isenberg directly or from an Isenberg authorized dealer, and installed in the United States or Canada. This warranty is non-transferrable. The following exceptions shall apply to the Warranty Period for homeowners: (1) Standard Special finishes (i.e., any finish outside of Chrome and Brushed Nickel) shall be limited to a period of 3 years from the original date of purchase; (2) Living Finishes including polished brass and brushed brass finishes warranty shall be limited to a period of 1 year from the original date of purchase; (3) All chrome and brushed nickel finishes on cover plates and all handles shall be limited to a period of 3 years from the original date of purchase. In addition, the Warranty Period for drain assemblies, bathroom hoses, hand-helds, kitchen hand sprays and kitchen hoses shall be limited to a period of 1 year from the original date of purchase. This warranty is extensive in that it covers replacement of all defective parts and finishes, but these are the only two things that are covered. Damage due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether performed by a contractor, service company, or you, are excluded from this warranty. Further, this warranty will not apply if you do not use the product in its entirety. If any part (including but not limited to a cartridge, hose, handle, o-ring, aerator, flow limiting restrict-or, etc.), is not installed, removed, or replaced by a non-genuine Isenberg part, this warranty will be voided. Your sole and exclusive remedy, and Isenberg’s sole obligation, in case of a defective part or finish is to have Isenberg, at Isenberg’s sole option, repair or replace the defective part or finish. By way of example but not limitation, the following costs and expenses are not covered by this warranty: (i) labor costs for the removal, installation, re-installation, finishing or refinishing of the product, or defective part (or of building materials which must be removed, installed, reinstalled, finished or refinished in order to repair or replace the defective product or part); (ii) shipping and freight expenses required to return product to Isenberg. Repaired or replaced parts are individually warranted only under the same terms and for the remaining balance of the warranty period applicable to that part(s) which is/are repaired or replaced. IN NO EVENT, WILL ISENBERG BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES INCLUDING, BUT NOT LIMITED TO, LABOR, REMOVAL, RE-INSTALLATION, REFINISHING, LOSS OF USE OF THE PRODUCT, LOSS OF PROFITS, LOSS OF REVENUE, LOST GOODWILL, CLAIMS OF EMOTIONAL DISTRESS, OR CLAIMS OF WARRANTY HOLDERS’ CUSTOMERS, WHETHER BASED ON CONTRACT, WARRANTY, TORT (INCLUDING, BUT NOT LIMITED TO, STRICT LIABILITY OR NEGLIGENCE) OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. EVEN IF THIS WARRANTY IS DEEMED TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL ISENBERG’S ENTIRE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT WARRANTED HEREUNDER. THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES NOT EXPRESSLY SET FORTH HEREIN, WHETHER EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT THAT ANY IMPLIED WARRANTIES MAY NONETHELESS EXIST BY OPERATION OF LAW, ANY SUCH WARRANTIES ARE LIMITED TO THE DURATION PROVIDED BY THAT LAW. SOME STATES/PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. Compliance with Local Codes Isenberg makes no representations that its products or its installation instructions comply with any or all local building or plumbing codes. It is your responsibility to determine local code compliance and correct usage. Isenberg strongly recommends using a licensed and insured plumber to install or service your Isenberg product. Warranty Claims Contact Information You may make a warranty claim or order replacement parts by calling Isenberg Bath’s Corporate office at +1-888-342-2284, or by writing to Isenberg Bath Corporation, P O BOX 630283, Irving TX 75063. Proof of purchase (original sales receipt) must accompany all warranty claims. To receive assistance or service under this warranty, you will be asked to provide a description of the problem, the model number of the product, your contact information, and the date of purchase. Isenberg may, at its option, also request that you, at your expense, mail the defective part or product to Isenberg for inspection.
Key Specs
Collection:
Series 240
Item Category:
Sink Faucet
Flow Rate @ 60 PSI:
1.2
Style:
Transitional
Dimensions:
13 × 3.5 × 17.25 in
ADA Compliant:
No
WaterSense Compliant:
Yes
Installation Type:
Wall Mount
Number Of Handles:
2
Specifications:
Solid Brass Construction
Specifications:
Includes Rough In Valve – WLM.1900
Specifications:
Separate Hot And Cold Handles
Specifications:
Extension Available – Part # 240.1950E**
WARRANTY:
Limited Lifetime Warranty, See Warranty page for complete details
SKU:
SPOV137-863
Weight:
6.80 LBS
(No reviews yet) Write a Review
$642.00
Square Feet Needed:

INCLUDE WASTE

no waste 5% waste 10% waste
It is recommended you order 5% or 10% waste, depending on the size and layout of your project. Check one of the 'INCLUDE WASTE' options on the product page to automatically add 5% or 10% waste to your order. You may require more or less waste for your specific project.
  • 0 SQFT   (     )
  • $642.00   per SQFT
  • ( $642.00   per Box)
  • Waste : 0 SQFT
  • Total: $00.00
SQF PER BOX: